OPERATOR’S MANUAL
PD30X-XXX-XXX-C
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
PE30X-XXX-XXX-C
RELEASED:
REVISED:
(REV. 07)
2-9-05
1-16-11
3" DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material op-
tions.
637303-XX for fluid section repair (see page 4). NOTE: This kit also
contains several air motor seals which will need to be replaced.
637374-X major air valve assembly (see page 7).
637421 for air section repair (see page 6).
PUMP DATA
Models. . . . . . . . . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type. . . . . . . . . . . . . Metallic Air Operated Double Diaphragm
Material. . . . . . . . . . . . . . . . see Model Description Chart
Weight . . PX30A-XAX-XXX-C. . . . . . . . . . . . 129.5 lbs (58.8 kgs)
Figure 1
PX30A-XCX-XXX-C. . . . . . . . . . . . 216.6 lbs (98.2 kgs)
PX30A-AHX-XXX-C, -BHX . . . . . 249.8 lbs (113.3 kgs)
MODEL DESCRIPTION CHART
PX30A-ASX-XXX-C, -BSX . . . . . . 228.8 lbs (103.8 kgs)
PX30A-FHX-XXX-C. . . . . . . . . . . . 269.6 lbs (122.3 kgs)
P X 30 X - X X X - X X X - C
PX30A-FSX-XXX-C . . . . . . . . . . . . 245.6 lbs (111.4 kgs)
(add 40.0 lbs [18.2 kg] for stainless steel air motor section)
Maximum Air Inlet Pressure . . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure. . . . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate . . . . . . . . . . . . . . . . . . . 237 g.p.m. (897 l.p.m.)
flooded inlet . . . . . . . . . . . 275 g.p.m. (1041 l.p.m.)
Electronic Interface
D - None
Available
E
-
Air Motor / Air Cap Material
A - Aluminum / Aluminum
S
-
Stainless steel / Stainless steel
Displacement / Cycle @ 100 p.s.i.g. . . . . 2.8 gal. (10.6 lit.)
Maximum Particle Size . . . . . . . . . . . . . . . . 3/8”dia. (9.5 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)
Hytrel® . . . . . . . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)
Kynar® PVDF . . . . . . . . . . . . . . . . . . . 10° to 200° F (-12° to 93° C)
Nitrile . . . . . . . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)
Santoprene® . . . . . . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Viton®. . . . . . . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)
Dimensional Data. . . . . . . . . . . . . . . . . . . . . . see page 8
Fluid Connection
A - 3 - 8 N.P.T.F. - 1
B - Rp 3 (3 - 11 BSP parallel)
F
-
3”ANSI / DIN Flange
Fluid Cap & Manifold Material
A - Aluminum
C - Cast Iron
H - Hastelloy®- C
Stainless steel
S
-
Hardware Material
P
S
-
-
Carbon steel
Stainless steel
Mounting Dimensions . . 10-5/32”x 12-1/16”(258 mm x 306 mm)
Seat Material
A - Santoprene
C - Hytrel
H - Hard 440 stainless steel
K - Kynar PVDF
Noise Level @ 70 p.s.i., 50 c.p.m. . . . . . . 83.0 db(A)
c
d
E
F
-
-
Carbon steel
Aluminum
L
S
-
-
Hastelloy - C
316 Stainless steel
Tested with 67263 muffler assembly installed.
c
d
The pump sound pressure levels published here have been updated to
an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.
G - Nitrile
Ball Material
A - Santoprene
C - Hytrel
T
-
PTFE
V - Viton
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or
the factory if you have questions concerning availability.
G - Nitrile
Diaphragm Material
A - Santoprene
B - Santoprene (backer)
C - Hytrel
G - Nitrile
PTFE / Santoprene
V - Viton
T
-
Fluid Section Service Kit Selection
PD30X - XXX - X X X - C
637303 - X X
Example: Model #PD30A-ACS-SVT-C
Fluid Section Service Kit # 637303-VT
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
© 2011
CCN 15227648
(800) 495-0276 FAX(800) 892-6276
ꢀ
GENERAL DESCRIPTION
MAINTENANCE
The ARO diaphragm pump offers high volume delivery even at low
air pressure and a broad range of material compatibility options are
available. Refer to the model and option chart. ARO pumps feature
stall resistant design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differen-
tial in the air chambers to alternately create suction and a positive
fluid pressure in the fluid chambers, valve checks insure a positive
flow of fluid.
Pump cycling will begin as air pressure is applied and will continue
to pump and keep up with the demand. It will build and maintain
line pressure and will stop cycling once maximum line pressure is
reached (dispensing device closed) and will resume pumping as
needed.
Refer to the part views and descriptions as provided on pages 4
through 7 for parts identification and service kit information.
Certain ARO “Smart Parts” are indicated which should be avail-
able for fast repair and reduction of down time.
Service kits are divided to service two separate diaphragm
pump functions: 1. AIR SECTION, 2. FLUID SECTION. The Fluid
Section is divided further to match typical part Material Op-
tions.
y
y
Provide a clean work surface to protect sensitive internal mov-
ing parts from contamination from dirt and foreign matter dur-
ing service disassembly and reassembly.
y
Keep good records of service activity and include the pump in
preventive maintenance program.
Before disassembling, empty captured material in the outlet
manifold by turning the pump upside down to drain material
from the pump.
y
y
AIR AND LUBE REQUIREMENTS
EXCESSIVE AIR PRESSURE. Can cause pump dam-
WARNING
age, personal injury or property damage.
FLUID SECTION DISASSEMBLY
A filter capable of filtering out particles larger than 50 microns
should be used on the air supply. There is no lubrication re-
quired other than the “O” ring lubricant which is applied during
assembly or repair.
If lubricated air is present, make sure that it is compatible with
the “O”rings and seals in the air motor section of the pump.
y
y
1. Remove (61) outlet manifold and (60) inlet manifold.
2. Remove (22) balls, (19) “O”rings (if applicable) and (21) seats.
3. Remove (15) fluid caps.
NOTE: Only PTFE diaphragm models use a primary diaphragm (7)
and a backup diaphragm (8). Refer to the auxiliary view in the Fluid
Section illustration.
4. Remove the (14) screw, (6) diaphragm washer, (7) or (7 / 8) dia-
phragms, (5) backup washer and (196) cushion.
OPERATING INSTRUCTIONS
NOTE: Do not scratch or mar the surface of (1) diaphragm rod.
Always flush the pump with a solvent compatible with the ma-
terial being pumped if the material being pumped is subject to
“setting up”when not in use for a period of time.
Disconnect the air supply from the pump if it is to be inactive
for a few hours.
The outlet material volume is governed not only by the air sup-
ply, but also by the material supply available at the inlet. The
material supply tubing should not be too small or restrictive.
Be sure not to use hose which might collapse.
When the diaphragm pump is used in a forced-feed (flooded
inlet) situation, it is recommended that a “check valve” be in-
stalled at the air inlet.
Secure the diaphragm pump legs to a suitable surface to insure
against damage by vibration.
y
FLUID SECTION REASSEMBLY
y
y
SERVICE NOTE: ARO pn 204214-T diaphragm assembly tool is rec-
ommended for use when reassembling the pump.
Reassemble in reverse order. Refer to the torque requirements
on page 5.
Clean and inspect all parts. Replace worn or damaged parts
with new parts as required.
Lubricate (1) diaphragm rod and (144) “U” cups with Lubriplate®
FML-2 grease (94276 grease packet is included in service kit).
Be certain the diaphragm assembly bottoms out on the (1) rod,
back off PTFE diaphragm assembly far enough to align holes.
For models with PTFE diaphragms: Item (8) Santoprene dia-
phragm is installed with the side marked “AIR SIDE” towards the
pump center body. Install the (7) PTFE diaphragm with the side
marked “FLUID SIDE”towards the (15) fluid cap.
y
y
y
y
y
y
y
Re-check torque settings after the pump has been re-started
and run a while.
y
Hytrel® and Viton® are registered trademarks of the DuPont Company Loctite® is a registered trademark of Henkel Loctite Corporation Kynar® is a registered trademark of Arkema Inc.
y
y
y
y
Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. ARO® is a registered trademark of Ingersoll-Rand Company
y
y
y
Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) 262™, 271™ and 572™ are trademarks of Henkel Loctite Corporation
y
y
y
Hastelloy® is a registered trademark of Haynes International, Inc.
y
y
PD30X-XXX-XXX-C (en)
Page 3 of 8
PARTS LIST / PX30X-XXX-XXX-C FLUID SECTION
637303-XX Fluid section service kit includes: Balls (see Ball Option, refer to -XX in chart below), Diaphragms (see Diaphragm Option, refer to -XX in chart
below) and items 3, 19, 70, 144, 175, 196 (listed below) and 174 and 94276 Lubriplate FML-2 grease (page 6).
n
SEAT OPTIONS PX30X-XXX-XXX-C
BALL OPTIONS PX30X-XXX-XXX-C
(3-1/4” diameter)
(3/16” x 5” o.d.)
“19”
“21”
“22”
n
n
-XXX Seat
Qty Mtl
(4) [Sp]
-XXX Seat
Qty Mtl
(4) [SH]
-XXX Ball
Qty Mtl “O” Ring
(4) [Sp] 94115
Qty Mtl
-AXX 94104-A
-CXX 94104-C
-EXX 95678
-FXX 95674
-GXX 94104-G
-HXX 94114
-KXX 94621-K
-LXX 94939
-SXX 94113
-XAX 94103-A
-XCX 94103-C
-XGX 94103-G
-XTX 94103-T
-XVX 94103-V
(4)
(4)
(4)
(4)
(4)
[E]
[V]
[B]
[T]
[V]
(4)
(4)
(4)
(4)
[H]
[C]
[A]
[B]
(4)
[K]
(4)
(4)
(4)
(4)
[H] Y327-350
[B] Y325-350
[T] Y328-350
[V] Y327-350
(4) [Ha]
(4) [SS]
NOTE: Seat options -AXX, -CXX and -GXX do not require item 19 "O" ring.
MATERIAL CODE
DIAPHRAGM OPTIONS PX30X-XXX-XXX-C
[A] = Aluminum
[B] = Nitrile
[C] = Carbon Steel
[Co] = Copper
[CI] = Cast Iron
[E] = E.P.R.
[H] = Hytrel
[Ha] = Hastelloy - C
[K] = Kynar PVDF
[SH] = Hard Stainless Steel
[Sp] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
(1/8” x 1” o.d.)
“3”
Service kit
-XX = (Ball)
-XX = (Diaphragm)
“7”
“8”
n
n
n
n
-XXX
Diaphragm
Qty
Mtl Diaphragm
Qty
Mtl “O” Ring
Qty
Mtl
-XXA 637303-XA
-XXB 637303-XB
-XXC 637303-XC
-XXG 637303-XG
-XXT 637303-XT
-XXV 637303-XV
94091-A
94110-A
94091-C
94091-G
94090-T
95345
(2)
(2)
(2)
(2)
(2)
(2)
[Sp] - - - - -
[Sp] - - - - -
[H] - - - - -
[B] - - - - -
[T] 94110-A
[V] - - - - -
- - -
- - -
- - -
- - -
(2)
- - - Y328-210
- - - Y328-210
- - - Y327-210
- - - Y328-210
[Sp] Y328-210
- - - Y327-210
(2)
(2)
(2)
(2)
(2)
(2)
[T]
[T]
[V]
[T]
[T]
[V]
[V] = Viton
- - -
CENTER SECTION PART OPTIONS PX30X-XXX-XXX-C
PD30A-XXX-XXX-C PE30A-XXX-XXX-C PD30S-XXX-XXX-C PE30S-XXX-XXX-C
(size)
Item
Description
Qty Part No.
(2) 94831-1
(1) 94030-1
(1) 94030-2
(1) - - - - -
Mtl Part No.
[C] 94831-1
[A] 94721-1
[A] 94721-2
- - - Y17-50-S
- - - Y17-51-S
[C] 94531
Mtl Part No.
[C] 94831-2
[A] 94031-1
[A] 94031-2
[SS] - - - - -
[SS] Y17-51-S
[C] 96656
[B] - - - - -
Mtl Part No.
[SS] 94831-2
[SS] 94031-1
[SS] 94031-2
- - - Y17-50-S
[SS] Y17-51-S
[SS] 96656
- - - - - - - -
[B] Y325-118
[SS] Y178-56-S
Mtl
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
- - -
5
Backup Washer
68 Air Cap
69 Air Cap
76 Pipe Plug
126 Pipe Plug
(1/8 - 27 N.P.T. x 0.27”)
(1/4 - 18 N.P.T. x 7/16”)
(2) - - - - -
(M10 x 1.5 - 6g x 120 mm)
(3/32” x 1” o.d.)
131 Screw
(4) 94531
(2) Y325-117
(2) - - - - -
“O” Ring
[B] Y325-117
- - - - - - - -
175
no
no
(3/32” x 1-1/16” o.d.)
(5/32” o.d. x 3/4” long)
- - - Y325-118
- - - Y178-56-S
[B]
181 Roll Pin
(4) - - - - -
- - - - - - - -
[SS]
MANIFOLD THREAD / FLUID CAP MATERIAL OPTIONS PX30X-XXX-XXX-C
PX30X-XAX-XXX-C PX30X-XCX-XXX-C PX30X-XHX-XXX-C PX30X-XSX-XXX-C PX30X-FSX-XXX-C PX30X-FHX-XXX-C
(size)
Qty Part No.
Mtl Part No.
Mtl Part No.
Mtl Part No.
Mtl Part No.
Mtl Part No.
Mtl
Item Description
6
9
Diaphragm Washer
Washer
(2) 94802
[A] 94803
[SS] 94947
[Ha] 94803
[Ha] Y13-12-T [SS] Y13-12-T [SS] 94949
[Ha] Y5-134-T [SS] Y5-134-T [SS] 94948
[SS] 94803
[SS] 94947
[Ha]
[Ha]
[Ha]
[Ha]
[SS]
[Ha]
[Ha]
(2) Y13-12-T [SS] Y13-12-T [SS] 94949
(2) Y5-134-T [SS] Y5-134-T [SS] 94948
(2) 94024
(2) - - - - -
(3/4” - 16 x 3-1/4”)
14 Cap Screw
15 Fluid Cap
32 Leg
60 Inlet Manifold
61 Outlet Manifold
[A] 94106
- - - 94701-1
[A] 94305-[
[CI] 94693
[Ha] 94107
[SS] 94107
[SS] 94693
[SS] 94703-2
[SS] 96811 [
[SS] 96810 [
[C] 94703-2 [SS] 94703-2 [SS] 94703-2
[CI] 94691-[
[CI] 94809-[
94699-[
]
]
]
]
]
]
[Ha] 94216-[
[Ha] 94704-[
]
]
[SS]
[SS]
[
[
]
]
(1)
(1)
p
p
p
p
96785
96784
p
p
]
94700-[
[A] 94702-[
p
p
p
p
p
p]
EXTERNAL HARDWARE OPTION PX30X-XXX-XXX-C
PX30X-XXP-XXX-C PX30X-XXS-XXX-C
(size)
Item
26 Screw
27 Screw
Description
Qty Part No.
(12) 94412-1
(16) 94991-1
(16) 95053-1
Mtl Part No.
[C] 94412-2
[C] 94991
[C] 95053
Mtl
[SS]
[SS]
[SS]
(M12 x 1.75 - 6g x 45 mm)
(M12 x 1.75 - 6g x 60 mm)
(M12 x 1.75 - 6h)
29 Nut
COMMON PARTS
(size)
(size)
Item
q
Description
Rod
Qty Part No.
(1) 94984
(1) 93004
(2) 94100
Mtl
Item
Description
Qty Part No.
(2) Y186-51
(4) 94098
(2) 94631
Mtl
[B]
[Co]
[Sp]
(3/16” x 1-3/8” o.d.)
1
[C]
[Co]
[B]
144 “U” Cup
180 Gasket
196 Cushion
no
o
n
(see page 7)
(0.406” i.d. x 0.031” thick)
43 Ground Lug
70 Gasket
no
Air motor kit parts, see pages 6 and 7.
For N.P.T.F. thread models (PX30X-AXX-XXX-C) use "-1".
For BSP thread models (PX30X-BXX-XXX-C) use "-2".
“Smart Parts“, keep these items on hand in addition to the service kits for fast
repair and reduction of down time.
o
p
ꢁ
q
Page 4 of 8
PD30X-XXX-XXX-C (en)
PARTS LIST / PX30X-XXX-XXX-C FLUID SECTION
COLOR CODE
Diaphragm
Ball
3
2
1
4
Material
Color
Color
Hytrel
Nitrile
Santoprene
Santoprene
(backup)
PTFE
Cream
Black
Tan
Cream
Red (•)
Tan
5
7
8
6
Green
N / A
61
White
White
Viton
Yellow (-) Yellow (•)
(-) Stripe
(•) Dot
FOR THE AIR MO-
TOR SECTION, SEE
PAGES 6 & 7.
Torque Sequence
61
26 ꢀꢁ
68 181
175
ꢂ
70
ꢂ
76
ꢃ
175
ꢂ
70
ꢂ
1
5
196
7
6
14 ꢀꢅ
22
21
19
ꢂ
27 ꢀ
ꢃ
126
144
ꢂ
ꢂ
144
15
22
29
ꢁ
69
180
131 ꢀꢄ
ꢂ
3
9
60
26 ꢀꢁ
19
21
ꢂ
32
26
60
ASSEMBLY TORQUE REQUIREMENTS
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
)
(
Figure 2
View for PX30X-XXX-XXT-C (PTFE diaphragm) con-
figuration only.
(14) cap screw, 65 - 70 ft lbs (88.1 - 94.9 Nm).
(26) screw, 60 - 70 ft lbs (81.3 - 94.9 Nm).
(27) screw, 60 - 70 ft lbs (88.1 - 94.9 Nm).
(131) screw, 35 - 40 ft lbs (47.5 - 54.2 Nm).
LUBRICATION / SEALANTS
Apply Lubriplate FML-2 grease to all “O” rings, “U” cups and mating parts.
Apply Loctite® 271™ to threads.
c
d
e
Apply anti-seize compound to threads and bolt and nut flange heads
which contact pump case when using stainless steel fasteners.
Apply Loctite 262™ to threads at assembly.
f
g
h
i
Apply PTFE tape to threads.
Apply Loctite 572™ to threads.
(Santoprene)
(PTFE)
8
7
Not used with PX30X-XXX-AXX-C, -CXX and -GXX.
Note: Lubriplate FML-2 is a white food grade petroleum grease.
PD30X-XXX-XXX-C (en)
Page 5 of 8
PARTS LIST / PX30X-XXX-XXX-C AIR MOTOR SECTION
Indicates parts included in 637421 air section service kit shown below and items (70), (144), (175) and (180) shown on page 4.
o
AIR MOTOR PARTS
(size)
(size)
Item
101
Description
Qty Part No.
(1) 94028
(1) 94109
(1) 94092
(4) 95887
(1) 95651
(2) 94083
(2) 94084
(1) 94860
(2) Y29-42-S
(1) 94099
Mtl
Item
Description
Qty Part No.
(1) 94026
(1) 67164
(2) 94433
(1) Y240-9
(1) 94081
(1) Y325-119
(1) Y325-22
(2) Y325-26
(2) Y325-202
(2) 94102
(1) 95666
(1) 95665
(1) 67213
(1) 96336
(1) 96338
(2) 95991
(1) 96344
(1) Y325-5
(1) Y325-204
(1) Y325-208
Mtl
[B]
[D]
[U]
[B]
[Br]
[B]
[B]
[B]
[B]
[Sp]
[B]
[B]
(PX30A-XXX-XXX-C)
(PX30S-XXX-XXX-C)
Center Body
[A]
166 Track Gasket
167 Pilot Piston
to
o
(includes 168 and 169)
[SS]
[D]
(3/32” x 5/8” o.d.)
(1/8” x 7/8” o.d.)
103 Bushing
168 "O” Ring
169 “U” Cup
(M6 x 1 - 6g x 20 mm)
105 Screw
[SS]
[D]
111 Spool
170 Piston Sleeve
(0.250” x 2.276” long)
(1-1/2 - 11-1/2 N.P.T.)
(3/32” x 1-1/8” o.d.)
118 Actuator Pin
121 Sleeve
[SS]
[D]
171 “O” Ring
172 “O” Ring
173 “O” Ring
174 “O” Ring
o
o
(1/16” x 1-1/8” o.d.)
(1/16” x 1-3/8” o.d.)
(1/8” x 1/2” o.d.)
(check valve)
127 90° St. Elbow
[C / I]
[SS]
[B]
o
(1/4” - 20 x 1/4”)
128 Set Screw
132 Gasket
no
o
176 Diaphragm
199 Track Gasket
200 Gasket
o
(1/4”) (PX30A-XXX-XXX-C)
(PX30S-XXX-XXX-C)
Lockwasher
(3) Y117-416-C [C]
133
o
(3) Y14-416-T
(4) 96358
[SS]
[SS]
[A]
o
(M6 x 1 - 6g x 30 mm)
(includes item 127)
134 Screw
201 Muffler Kit
Adapter Plate
233
(PD30A-XXX-XXX-C)
(PD30S-XXX-XXX-C)
(PE30A-XXX-XXX-C)
(PE30S-XXX-XXX-C)
(PX30A-XXX-XXX-C)
(PX30S-XXX-XXX-C)
Valve Housing
(1) 96334-1
(1) 96337-1
(1) 96334-2
(1) 96337-2
(1) 96335
[A]
[SS]
[SS]
[B]
135
[SS]
[A]
(M6 x 1 - 6g x 16 mm)
240 Screw
[SS]
[A]
241 Track Gasket
o
o
o
o
(PX30A-XXX-XXX-C)
(1/16” x 7/32” o.d.)
Plug
242 “O” Ring
243 “O” Ring
244 “O” Ring
[B]
136
(PX30S-XXX-XXX-C)
(1/16” x 2” o.d.)
(1/8” x 5/8” o.d.)
(1/8” x 7/8” o.d.)
(1) 96339
[SS]
[B]
[B]
137 “O” Ring
138 “U” Cup
139 “U” Cup
(1) Y325-32
(1) 95966
[B]
o
o
o
(3/16” x 1.792” o.d.)
(3/16” x 1-1/4” o.d.)
[B]
(1) Y186-50
(1) 95650
[B]
Lubriplate FML-2 grease
(1) 94276
637308
n o
140 Valve Insert
141 Valve Plate
(Ck)
(Ck)
[B]
Lubriplate Grease Packets (10)
(1) 95659
Items included in fluid section service kit, see pages 4 and 5.
Used on models PX30S-XXX-XXX-C only.
Used on models PX30A-XXX-XXX-C only.
n
s
t
(3/32” x 1-1/16” o.d.)
146 “O” Ring
147 “O” Ring
(1) Y325-118
(2) Y325-202
so
so
(1/8” x 1/2” o.d.)
[B]
MATERIAL CODE
3. Install new (168) “O”rings and (169) seal - Note the lip direction.
Lubricate and replace (167) pilot piston.
[A] = Aluminum
[B] = Nitrile
[Br] = Brass
[C] = Carbon Steel
[Ck] = Ceramic
[D] = Acetal
[I] = Iron
[Sp] = Santoprene
[SS] = Stainless Steel
[U] = Polyurethane
4. Reassemble remaining parts. Replace (173 and 174) “O”rings.
MAJOR VALVE DISASSEMBLY
1. Remove (135) valve housing and (233) adapter plate, exposing
(132 and 166) gaskets and (176) checks.
AIR MOTOR SECTION SERVICE
Service is divided into two parts - 1. Pilot Valve, 2. Major Valve.
GENERAL REASSEMBLY NOTES:
2. Remove (233) adapter plate, releasing (140) valve insert, (141)
valve plate, (199, 200 and 241) gaskets and (243 and 244) “O”
rings.
Air Motor Section service is continued from Fluid Section repair.
y
Inspect and replace old parts with new parts as necessary. Look
3. Remove (136) plug and (137) “O”ring, releasing (111) spool.
y
for deep scratches on metallic surfaces, and nicks or cuts in “O”
rings.
MAJOR VALVE REASSEMBLY
Take precautions to prevent cutting “O”rings upon installation.
Lubricate “O”rings with Lubriplate FML-2 grease.
Do not over-tighten fasteners. Refer to torque specification
block on view.
Re-torque fasteners following restart.
SERVICE TOOLS - To aid in the installation of (168) “O”rings onto
the (167) pilot piston, use tool # 204130-T, available from ARO.
y
y
y
1. Install new (138 and 139) “U” cups on (111) spool - LIPS MUST
FACE EACH OTHER.
2. Insert (111) spool into (135) valve housing.
3. Install (137 and 242) “O” rings on (136) plug and assemble plug
to (135) valve housing, securing with (105) screws.
4. Install (140) valve insert, (141) valve plate, (199) gasket and (243
and 244) “O“ rings into (135) valve housing. NOTE: Assemble
(140) valve insert with “dished” side toward (141) valve plate.
Assemble (141) valve plate with part number identification to-
ward (140) valve insert.
y
y
PILOT VALVE DISASSEMBLY
1. A light tap on (118) actuator pin should expose the opposite
(121) sleeve, (167) pilot piston and other parts.
2. Remove (170) sleeve. Inspect inner bore of sleeve for damage.
5. Assemble (200 and 241) gaskets and (233) adapter plate to (135)
valve housing, securing with (240) screws.
6. Assemble (132 and 166) gaskets and (176) checks to (101) cen-
ter body.
7. Assemble (135) valve housing and components to (101) center
body, securing with (134) screws.
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Install new (171 and 172) “O”rings. Replace (170) sleeve.
Page 6 of 8
PD30X-XXX-XXX-C (en)
PARTS LIST / PX30X-XXX-XXX-C AIR MOTOR SECTION
Substitute these “O“ rings for
j
PILOT VALVE
PART GROUP
(166) gasket on models PX30S-
XXX-XXX-C.
118
ꢂ
169 168
ꢂ
147
146
ꢂ
172
ꢂ
ꢂ
ꢂ
ꢂ
174
121
173
167
171ꢂ
170
173
121
118
174
ꢂ
ꢂ
140 199
ꢂ
244
ꢂ
243
ꢂ
233 132
ꢂ
166 ꢂꢆ
135
103
101
133
134
43
ꢁ
141
ꢂ
241
200
ꢂ
128
ꢅ
240 ꢀꢁ 176
ꢂ
ꢂ
138
ꢂ
Optional 94117 Muffler
111
139
242
128
ꢂ
ꢂ
ꢅ
ꢂ
137
136
201
127
105 ꢀꢁ
MAJOR VALVE
Figure 3
ASSEMBLY TORQUE REQUIREMENTS
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
LUBRICATION / SEALANTS
)
(
Apply Lubriplate FML-2 grease to all “O” rings, “U” cups and mat-
ing parts.
c
Apply Loctite 271 to threads.
d
e
(105) screw, 40 - 50 in. lbs (4.5 - 5.6 Nm).
(134) screw, 40 - 50 in. lbs (4.5 - 5.6 Nm).
(240) screw, 40 - 50 in. lbs (4.5 - 5.6 Nm).
Apply anti-seize compound to threads and bolt and nut flange
heads which contact pump case when using stainless steel fas-
teners.
A replacement major valve service assembly is available separately, which includes the following:
637374-2 for models PD30A-XXX-XXX-C: 105 (4), 111, 128 (2), 132, 133 (3), 134 (4), 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 233, 240 (2),
241, 242, 243 and 244.
637374-3 for models PE30A-XXX-XXX-C: 76, 105 (4), 111, 128 (2), 132, 133 (3), 134 (4), 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 233, 240 (2),
241, 242, 243 and 244.
637374-4 for models PD30S-XXX-XXX-C: 105 (4), 111, 128 (2), 132, 133 (3), 134 (4), 135, 136, 137, 138, 139, 140, 141, 146, 147, 176 (2), 199, 200, 233, 240 (2),
241, 242, 243 and 244.
637374-5 for models PE30S-XXX-XXX-C: 76, 105 (4), 111, 128 (2), 132, 133 (3), 134 (4), 135, 136, 137, 138, 139, 140, 141, 146, 147, 176 (2), 199, 200, 233, 240
(2), 241, 242, 243 and 244.
PD30X-XXX-XXX-C (en)
Page 7 of 8
TROUBLE SHOOTING
Product discharged from exhaust outlet.
Low output volume, erratic flow or no flow.
Check for diaphragm rupture.
Check air supply.
y
y
y
y
y
y
y
Check tightness of (14) cap screw.
Check for plugged outlet hose.
Check for kinked (restrictive) outlet material hose.
Check for kinked (restrictive) or collapsed inlet material hose.
Check for pump cavitation - suction pipe should be sized at
least as large as the inlet thread diameter of the pump for
proper flow if high viscosity fluids are being pumped. Suction
hose must be a non-collapsing type, capable of pulling a high
volume.
Air bubbles in product discharge.
Check connections of suction plumbing.
Check “O”rings between intake manifold and fluid caps.
Check tightness of (14) cap screw.
y
y
y
Motor blows air or stalls.
Check (176) check valve for damage or wear.
Check for restrictions in valve / exhaust.
Check all joints on the inlet manifolds and suction connections.
These must be air tight.
Inspect the pump for solid objects lodged in the diaphragm
chamber or the seat area.
y
y
y
y
DIMENSIONAL DATA
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
3 - 8 N.P.T.F. - 1 (PX30X-AXX-XXX-C)
Rp 3 (3 - 11 BSP parallel) (PX30X-BXX-XXX-C)
E
L
F
A
L
Outlet
B
Q (Bolt circle)
G
Air Inlet Ports
3/4 - 14 N.P.T.F. - 1
B
Q
N
D
D
P
H
Inlet
K
J
3” A.N.S.I / DIN Flange
(PX30X-FXX-XXX-C)
C
M
Exhaust Port 1-1/2 - 11-1/2 N.P.T.
D o t t e d l i n e s s h o w
optional 67263 muffler
assembly.
Figure 4
DIMENSIONS
A - see below
F
- 15”(381.0 mm)
K - 9/16” (14.3 mm)
P
- 1”(25.4 mm)
B - 30”(762.0 mm)
C - 12-1/16”(306.4 mm)
D - see below
G - see below
L
- see below
Q - 6”(152.4 mm)
H - 10-5/32” (258.0 mm)
J
M - 23-3/32” (586.3 mm)
N - see below
- see below
E
- 17-11/16”(449.2 mm)
“L”
“G”
“A”
“D”
“J”
“N”
2-3/4”(69.9 mm) 32”(812.8 mm)
2-3/4”(69.9 mm) 32”(812.8 mm)
2-3/4”(69.9 mm) 32”(812.8 mm)
2-3/4”(69.9 mm) 32”(812.8 mm)
PX30X-XAX-XXX-C
PX30X-XCX-XXX-C
PX30X-XHX-XXX-C
PX30X-XSX-XXX-C
PX30X-FXX-XXX-C
23-5/8”(600.1 mm) 2-3/8”(60.3 mm) 11”(279.4 mm)
15-1/2”(393.7 mm)
23-5/8”(600.1 mm) 2-7/16”(61.9 mm) 11-11/16”(296.9 mm) 15-1/2”(393.7 mm)
23-1/8”(587.4 mm) 2-3/4”(69.9 mm) 11-11/16”(296.9 mm) 16”(406.4 mm)
23-1/8”(587.4 mm) 2-3/4”(69.9 mm) 11-11/16”(296.9 mm) 16”(406.4 mm)
23-1/8”(587.4 mm) 2-3/4”(69.9 mm) 11-11/16”(296.9 mm) 16”(406.4 mm)
3-3/4”(95.25 mm) 33-3/4”(857.3 mm)
PN 97999-1110
Page 8 of 8
PD30X-XXX-XXX-C (en)
|
Indesit Refrigerator SA300 I User Manual
Intel Computer Hardware PX875P User Manual
JBL Speaker System CVIW50 User Manual
JVC Car Stereo System GET0287 003A User Manual
JVC Speaker TH BA1 User Manual
JVC Stereo System CA FS400 User Manual
Kenwood Radio KTC HR100 User Manual
KitchenAid Oven KAC 28 User Manual
KitchenAid Refrigerator W10326028A User Manual
Korg Musical Instrument musical instruments User Manual